GE Top-Load Washer Error Codes: Fill, Lid Lock, Drain and Fault Numbers

GE top-load washers do not use the same code language as GE front-loaders. A top-loader mostly talks through lights and short messages, and keeps a numbered fault history in memory. This guide is built from GE’s own technical service guides for two top-load families: the 27-inch top-load line (guide 31-9446, November 2024, models such as GTW220, GTW325, GTW385, GTW485, GTW500 and GTW525) and the CleanSpeak top-load washers (guide 31-9232, March 2014, GTWN7450, GTWN8250, GTWS8350, GTWS8650 and related models). If you own a GE front-load washer, you want our GE front-load washer error codes guide instead.

What a GE top-loader shows you on its own

GE calls the lights and messages on these washers the Consumer Help Indicator. They exist so you can sort out the simple cases without a service call, and GE lists four situations:

  • Spin light blinking. The washer detected an out-of-balance load and is working to correct it. If the clothes come out wetter than normal, GE’s advice is to spread the load evenly and run a Drain & Spin cycle.
  • Fill light flashing (or “H2O SUPPLY” on display models). Water is not entering the washer. GE’s first question is whether one or both supply valves were left off after installation or a trip. Two flashes mean the washer did not sense water collecting during fill; three flashes mean the cycle was paused for over 24 hours or water sat in the drum for 15 minutes with the lid open. Either way the controls lock for four minutes and the pump runs. Unplugging the washer to skip the wait restarts the four-minute timer.
  • “CAnCELEd”. The cycle was paused over 24 hours, water sat with the lid open for 15 minutes, or the washer stopped itself because of certain errors. Same four-minute lockout.
  • Lid Locked light flashing (or “Lid” on display models). Three cycles were started without opening the lid. The washer will not start another until the lid is opened and closed. GE sends anything that persists after that to service.

Those are the only items an owner can act on. The rest is technician territory.

How the stored fault codes are read

On the 27-inch models, GE built a Consumer Fault Mode so a caller can read the fault history to the person booking the visit. With the washer in standby and the cycle knob at 12 o’clock, press and hold Start for 10 seconds until every light comes on. The first stored fault shows, and each press of Start shows the next one. On models without a number display the code blinks in binary on the cycle status lights, so you report which lights are on; models GTW580 and higher use the number display. When the list ends, or if nothing is stored, all the status lights blink. Faults numbered above 100 are engineering faults and are never shown. Write the sequence down before you call, so the technician arrives with the right part.

The CleanSpeak washers work differently. Their codes are stored as hexadecimal values (digits and letters such as 9, A, B, D, E or CB) and are shown only in the technician’s Service Mode on the seven-segment display. A fault appears in that list only if it has actually occurred at least once. If you own a CleanSpeak, the visible symptom and the flashing lights are your information, and the technician reads the code.

27-inch top-load fault numbers: what they mean

The 31-9446 guide lists more than 60 fault values. Here is how they group.

Fault What the guide says it means What we check, and when to call
1, 2, 13, 14, 23, 24, 32 Lid lock and lid monitor faults: lock will not lock or unlock, or the control never got a lid-closed signal while the motor moved Lid lock, lid switch and harness. Call any time the lid will not lock or release
9 Three cycles run without the lid opening Open and close the lid first. Call only if the fault will not clear
3, 5, 10 Locked rotor, or the mode shifter (agitate and spin switch) did not engage in time Motor and drive, mode shifter, wiring. Call when the basket will not agitate or spin
16, 18, 25, 86 Slow drain, water still in the tub after draining, pressure drop without draining, low water pressure Drain pump, hose, standpipe height, pressure sensing. Call when water stays in the tub
6, 7, 12, 20, 52 Flood protection: level near overflow, max fill reached, pressure over 18.0 inches, more than 41 gallons in, or a water valve stuck open Water valves and the pressure system. Call at once if water keeps entering
8, 19, 21 Pressure sensor not seeing the expected change during fill, a cycle paused too long, or hot and cold hoses reversed Fill and pressure checks. Call if the fault repeats on a normal load
22, 26, 31 Out of balance: during dry-load sensing, ended final spin, or fell back to a slower final spin Load, leveling, suspension and basket. Call when it repeats on ordinary loads
Fault What the guide says it means What we check, and when to call
33-34, 41-51, 66-69, 71-75, 92 Inverter faults reported by the motor control board Line voltage, harnesses, motor windings, inverter board. Call when the washer will not spin
35, 36 Supply voltage under 102 VAC or over 132 VAC for 5 seconds House circuit. Call, and an electrician may be needed
53 Belt loss: belt detected as off the motor pulley Belt condition. Call, a new belt is fitted, not the old one
59-64, 87-90 Accelerometer board faults Harness and board. Call if a full spin does not complete
15, 76 Water temperature sensor invalid, or bulk-tank sensor failure Sensor and wiring. Call when temperature or dispensing is off
11, 58, 93 A main board component has failed Main board. Call, this is a board repair
28, 30, 78, 91, 99 Option knobs, a stuck button, board communication or Wi-Fi module problems Control and user interface. Call if the controls stop responding

The ones that matter urgently

Flood faults (6, 7, 12, 20, 52). If the washer is taking in water it should not, shut the supply valves and call. Fault 52 is set when the critical flood fault repeats while no cycle is running, and the guide’s conclusion points at the water valve itself. Voltage faults 35 and 36. If the supply is outside the 102 to 132 volt window, a new part will not help.

CleanSpeak hex codes in plain English

Code What the guide says it means What we check, and when to call
A, 10 No fill, or slow fill Supply, hose screens, lid switch, water valve. Call after you confirm both taps are open
B Drain pump: water remaining in the basket Standpipe height, pump, wiring. Call if water stays in the tub
9, E, 65, 66, 75 Lid lock will not lock or unlock Lid lock, switch, control. Call
16, 17, 18 Mode shifter not engaged to spin, to agitate, or too slow Mode shifter and coupler. Call when it will not agitate or spin
19 Flood protection: flood level detected Water valve and pressure sensor. Call at once
8, 68 Pressure sensor not filling as designed, or out of range Sensor, hose, control. Call
11, F, 6A, 6B Heater not reaching temperature, heater water-level check, thermistor open or short Heater and thermistor. Call when hot washes fail
D, 12, C9 to DF Control communication time-outs and inverter faults Control boards and wiring. Call if the washer is dead or will not spin
CB, CC, D2, D3 DC bus voltage, motor temperature, locked rotor, hall sensor Line voltage, motor, inverter. Call
5, 6, 76, 77 Bulk detergent or softener dispensing, or the bulk-tank sensors Dispense hoses, valves, sensors. Call

The guide also lists 1 (user interface memory), 7 (stuck button) and 72 (spin seen with the lid unlocked or open), all control-side faults.

Why we do not guess the part

Look at the tables: one lid-lock symptom appears under five different values, and the same fill problem can be a closed tap, a kinked hose, a clogged screen, the lid switch, the valve or the pressure sensor. GE’s repair actions for these codes are test steps, not part names. Out-of-balance faults often come down to how the load was packed or how level the washer sits. We read the stored list, test the suspect system live, quote the repair, and then order genuine OEM parts.

Repair or replace?

Lid locks, switches, drain pumps, water valves, belts and pressure sensors are routine repairs on a GE top-loader. An inverter, main board or motor on an older machine, or a second major repair within a year, is where we talk honestly about replacement. If the symptom is simply a washer that will not turn or empty, see washer won’t spin and washer not draining.

GE top-load washer repair across the Denver Metro

FiXiFY repairs GE washers in Denver, Aurora, Lakewood, Westminster and across the metro. Read the GE appliance repair page, the washing machine repair page, or the code guide for GE front-load washers.

BOOK ONLINECALL (303) 214-1240

FAQ

What does H2O SUPPLY mean on a GE top-load washer?

Water is not entering the washer, and GE’s first suggestion is to check that both supply valves are open. The controls then lock for four minutes while the pump runs, and unplugging the washer only restarts that timer. If the valves are open and it returns, the fill system needs testing.

Why does my GE top-loader say Lid or flash the Lid Locked light?

Three cycles were started without the lid being opened in between, and the washer will not start another until you open and close it. If it still refuses, the lid switch or lock is the likely cause.

How do I read the fault codes on a 27-inch GE top-load washer?

From standby with the cycle knob at 12 o’clock, hold Start for 10 seconds until every light comes on. Each Start press shows the next stored fault, in binary on the status lights for most models, and blinking lights or dashes mean the end of the list.

Does a GE CleanSpeak washer show an error code on the screen?

Not in normal use. CleanSpeak codes are hexadecimal values stored in the washer and read by a technician in Service Mode, and a fault is listed only if it has occurred at least once.

FiXiFY Appliance Repair — 7030 E 46th Ave Dr, Unit A, Denver, CO 80216 · (303) 214-1240 · support@fixifycolorado.com