You press Start. The dryer clicks, hums or even runs a motor you can hear, but when you open the door the clothes are exactly where you left them and the drum does not move. It is one of the more common dryer calls, and the service manuals treat it as its own problem with its own checklist. Here is what they say sits behind it, how to tell the versions of this problem apart, and why a dryer that hums without turning should be switched off rather than left to try again.
Three different problems that look alike
Describe what you hear before anything else, because the three versions point to different parts.
| What you see and hear | What the manuals point to |
|---|---|
| Nothing runs: no motor sound, no drum, no heat | Door switch, belt switch, motor circuit, thermal fuse or protector, control |
| Motor runs, drum stays still | Drive belt, idler pulley and its spring |
| Drum turns by hand but not under power | Same belt and idler path, or a motor that cannot start the load |
If the dryer does absolutely nothing, start with our guide to a dryer that will not start. This page is for the other two cases, where something is alive but the drum is not.
The manufacturers’ checklist for “drum will not spin”
Whirlpool’s service sheets for its electric and gas dryers have a row literally titled “Drum will not spin.” The possible causes it lists, in order, are the drive belt or belt switch, the thermal fuse on electric models, the door switch, the motor and the control board, followed by a check of the installation and the incoming power. A Whirlpool job aid for a related platform lists the same row without the belt switch: drive belt, door switch, motor and control. Samsung splits the symptom more finely. Its service manual has a line for “motor runs but tumbler does not turn,” with three causes: the belt is loose, broken or damaged, the idler tension spring is too weak or stretched, or the idler pulley is jammed or stuck.
LG’s motor test for its electric and gas dryers starts from the symptom “drum will not rotate; no fan will function; no heater will work.” Its flowchart walks through the door switch, the outlet thermostat, the idler switch on the motor bracket and the drum belt, and notes the belt may have cut off or come off the motor pulley.
The drive belt and idler pulley
Inside a typical dryer, one long belt wraps around the outside of the drum. GE’s service manual describes it as a four-rib belt that runs under the motor pulley, over the top of the idler pulley and around the perimeter of the drum. The motor turns a small pulley, the belt turns the drum, and a spring-loaded idler keeps the belt tight. GE’s small-dryer sheet gives the drum speed as roughly 47 to 51 revolutions per minute, and says belt tension is held by that spring-loaded idler.
When the belt snaps, stretches or slips off, the motor still runs and the blower may still move air, but nothing connects the motor to the drum. That is the “motor runs, drum does not turn” case in the Samsung chart. A weak idler spring or a jammed idler pulley does the same from the other direction, with the belt intact but not tight enough to grip. Samsung’s noise chart lists a sticky or frayed belt as a cause of popping or squealing.
The belt switch: why a broken belt can stop everything
Many dryers have a safety switch that watches the belt. GE explains that a switch activated by the idler arm is fastened to the motor bracket, and that if the drive belt breaks, the switch opens the drive motor circuit and interrupts dryer operation. Samsung lists a “belt cut-off” switch among its checkpoints for a dryer that does not run, and Whirlpool’s sheets list the belt switch as part of the motor circuit. LG’s flowchart has an equivalent idler switch.
The practical result is that a broken belt can show up in two ways. On a dryer with a belt switch, the motor may refuse to start at all, so it looks like a dead dryer. On a dryer without one, you hear the motor spin and the drum sits still. Which one you get depends on the model.
The motor, its start circuit and its overload protection
The drive motor is the other half of the belt story. GE’s manual describes a single-speed motor with an automatic-reset overload protector built into it, plus a centrifugal switch that takes the start winding out of the circuit once the motor is up to speed. Frigidaire’s laundry center manual says its dryer motor has an overload thermal protector that switches the motor off if it overheats.
Samsung’s chart for dryers that blow fuses or trip the breaker asks whether the belt is connected and whether the motor protector is normal. Whirlpool’s sheets also list the thermal fuse, but only for electric models: it is part of the motor circuit and has its own test.
The door switch
The drum motor is wired through the door switch, so a switch that does not register a closed door can stop the drum while other things still seem to work. Whirlpool lists it under “drum will not spin” and asks first that you make sure the door is fully closed and not striking the latch. LG’s motor test includes checking whether the door frame presses the switch knob. Frigidaire says its dryer motor is activated from the control board through the door switch.
What about the drum rollers and glides
The drum rides on support rollers or glides, and we check them on any drum-related visit. In the manuals we pulled, though, the rollers show up in the noise charts and the disassembly sections, not as an entry under a drum that will not turn. Samsung’s noise chart lists thumping from rear rollers that are worn or misaligned and scraping from worn front bearings, and its dryer flowchart for abnormal noise says to check the roller that supports and rotates the drum. Our dryer noise guide covers that. If your dryer thumped or squealed before it stopped turning, tell us; it helps the diagnosis.
What you can safely check, and what to stop doing
These steps need no tools and no meter:
- Make sure the door closes fully, with nothing caught at the latch, and press Start again.
- Take out part of the load. Samsung advises one wash load per dryer load.
- Switch the dryer off at the breaker or unplug it before you do anything else, including pulling it from the wall.
Do not open the cabinet, lift the top or try to turn the idler or belt yourself. GE’s own manual warns that the idler arm is under high tension and must not be allowed to snap back, and that sharp edges inside the cabinet call for cut-resistant gloves and sleeves.
Do not keep running a dryer that hums but does not turn
Pressing Start over and over is the habit to avoid. A motor that cannot turn its load gets hot, and the manuals build overload protectors into the motor because motors do overheat. A dryer that is heating a load that is not tumbling is also a poor idea with clothes inside. Samsung’s safety pages warn that lint buildup and flexible vent material raise the fire risk, so a dryer that is already struggling is the wrong one to leave unattended. Many Denver Metro homes keep the dryer in a garage or basement utility area beside shelves or a water heater, which is one more reason to shut it off and leave it off.
When to call, and what the repair looks like
If the dryer hums and does not turn, or turns by hand but not under power, book a repair. Whirlpool’s sheets put the drive belt and belt switch first on the list, and a technician checks them along with the motor circuit during the visit. We quote the repair before the work starts, and the diagnostic fee is credited toward it. If a manual gives a fault code for belt trouble, we use it: Frigidaire’s laundry center lists E56 as a belt fault and says to check the belt and replace it if it is broken or loose.
If the dryer also stops partway through cycles, see dryer stops mid-cycle; a dryer that never gets going and only clicks is covered under will not start.
Dryer repair across the Denver Metro
FiXiFY repairs electric and gas dryers of every brand across Denver, Aurora, Lakewood, Westminster and the metro, with genuine OEM parts and same-day visits in most areas. See our dryer repair service page or the repair guides hub.
BOOK ONLINECALL (303) 214-1240
FAQ
Why does my dryer run but the drum does not turn?
The usual cause is the drive belt, which may be broken, loose or off its pulleys, or an idler pulley or spring that no longer keeps it tight. The motor keeps running because it is not connected to the drum anymore. Samsung lists exactly these three causes for a motor that runs while the tumbler stays still.
Can a broken belt stop a dryer from starting at all?
Yes, on dryers with a belt switch. GE says the switch opens the motor circuit if the belt breaks, so the dryer will not run. Models without that switch simply run the motor with the drum standing still.
Is it safe to keep running a dryer that hums but does not tumble?
No. Stop it, switch it off at the breaker or unplug it, and take the clothes out. The motor is working against a load it cannot turn, and manuals add overload protectors to motors because they do overheat.
Can I fix a dryer belt myself?
We do not recommend it. GE’s manual warns that the idler arm is under high tension and can snap back, and that the cabinet has sharp edges. A technician diagnoses the belt, idler, switches and motor together, so a second failure is not missed.
FiXiFY Appliance Repair — 7030 E 46th Ave Dr, Unit A, Denver, CO 80216 · (303) 214-1240 · support@fixifycolorado.com
