Miele Refrigerator Error Codes: F 01 10, F 01 47 and What Each Fault Means

A Miele built-in refrigerator-freezer tells you about a fault in a very specific way: a code that starts with the letter F and is shown as a letter followed by four digits, for example F 01 10 or F 01 47. Some of the codes are meant for the technician only, and the factory documentation marks those as not visible to the customer. This guide explains what each code in the factory fault table means, which ones put your food at risk, and what a repair visit looks like. It is based on the Miele USA Technical Information KF 18xx / K 19xx Refrigerator-Freezers (Vi and SF Models), All US Models (2019). That is the MasterCool generation of built-in columns. Other Miele generations, including older freezers and the F 147x freezer family, use their own tables and displays, so do not assume this list fits every Miele you own.

How a Miele shows a fault

On this family the manual lists each code next to the way it is displayed: an F and four digits, so F41 appears as F 00 41 and F110 appears as F 01 10. The codes are stored by the control, and the technician’s service menu reports whether there are no saved faults or at least one, with room for a maximum of 10 stored faults. A code that came and went can still be read later.

Separate from fault codes, the control has two alarms that you will hear and see. The door alarm goes off after a door has been open for more than 5 minutes and stops when you close the door or touch the alarm icon. The temperature alarm sounds when a compartment gets too warm, and the manual lists the thresholds:

Compartment Alarm on Alarm off
Refrigerator 73°F 55°F
Freezer 27°F 15°F
SmartFresh drawers 50°F 37°F

The alarm is held back while the door is open and for 30 minutes after it closes, and during a defrost plus 30 minutes. An alarm still sounding well after you shut the door is real information. Write down any code on the display. The manual also notes that after a power interruption all icons are hidden and your last settings are saved, which is normal and not a fault.

The fault codes, grouped by system

The manual lists the codes below in one fault table. We have regrouped them by the part of the refrigerator they concern. The right-hand column summarizes what a technician checks.

Temperature sensors

Code What the manual says What we check, and when to call
F110 Refrigerator air NTC faulty The sensor and its reading. Call if the fresh-food side is too warm or too cold.
F111 Freezer air NTC faulty The sensor and its reading. Call if the freezer is not holding temperature.
F112 SmartFresh NTC faulty The drawer sensor. Call if produce is freezing or wilting.
F115, F116 Refrigerator (F115) or freezer (F116) evaporator NTC faulty The sensors that watch the cold coil. Call early; they affect defrost control.
F122 Ambient-air NTC faulty The room-temperature sensor. Book a visit; the unit usually keeps running.

An NTC is a temperature sensor whose electrical resistance changes with heat. The manual’s footnote says these codes appear when the resistance corresponds to a temperature below -66°F or above 140°F, which is far outside anything a real refrigerator reaches, so the sensor or its wiring has failed rather than the food actually being that cold or hot.

Compressor, cooling circuit and electronics

Code What the manual says What we check, and when to call
F41 Faulty power electronic The power board that drives the cooling system. Call the same day if nothing is cooling.
F123, F124 Refrigerator (F123) or freezer (F124): faulty electrical component, or faulty cooling circuit Electrical components first, then the sealed cooling circuit. Call the same day.
F127 Connection plug inserted incorrectly, or faulty control or power electronic The harness between the control and the power electronics, then the boards. Call the same day.
F120 Voltage below 95 VAC; the manual lists no remedy Not visible to you. Low supply voltage points to the outlet or the house circuit, which we check before any part.

Fans, ventilation and air flap

Code What the manual says What we check, and when to call
F147 Insufficient ventilation (toekick air grille blocked), faulty condenser fan, faulty power electronic, or faulty air flap Ventilation first, then the condenser fan, the air flap and the board. Call the same day.

Ice maker and water

Code What the manual says What we check, and when to call
F121 Faulty icemaker Water supply, pressure, dispenser flap and crusher before the ice maker itself. Call when ice stops.

Doors

Code What the manual says What we check, and when to call
F141, F142, F143 Refrigerator door open for 15, 30 or 45 minutes Close the door. Call if it keeps recurring with the door shut.
F144, F145, F146 Freezer door open for 15, 30 or 45 minutes Close the door. Call if it keeps recurring with the door shut.

The manual marks F120 and the six door codes F141 to F146 with an asterisk: they are not visible to the customer. They are stored in the control for the technician, so you will notice the symptom (the alarm, a warm compartment) and we will read the code.

Which codes mean food is at risk

Treat these as the urgent group: F41, F123, F124, F127 and F147. They concern the power electronics, the cooling circuit and the fans, which are the parts that actually make cold. The manual’s footnote on F147 is the most serious statement in the table: when a temperature above 135°F is detected in the compressor area three times, for at least 5 minutes each time, within a span of 127 minutes, the compressor is shut off to let that area cool down, and all components are shut off to avoid damaging them from the too-high temperatures. In plain terms, the refrigerator stops cooling to protect itself. If you see F 01 47, move perishables to a cooler with ice and call.

The sensor codes (F110, F111, F112, F115, F116) are the next tier. The unit may keep cooling, but the control has lost one of its readings, so temperatures can drift without a sensible correction. Our guide on a refrigerator not cooling because of a fan problem covers the symptoms that often go with them.

The manual also lists non-fault causes that look similar. Food lying in front of the air channel in a SmartFresh drawer can freeze, because cold air flows straight onto it, and the remedy is to move the food. That is worth remembering around Thanksgiving, when a packed fridge blocks the very vents the unit relies on. Ice forming inside the cabinet has several listed causes, from a defective defrost or drain heater to a door that does not seal; a door left open for a long time is checked by reading the stored codes.

The ice maker has its own fault light

Miele’s built-in ice maker is a separate module with its own fault LED. It reports faults by a blinking rhythm in three groups of flashes, and the manual says that if several faults occur only the most recent one is indicated. The table covers things like the ice production cycle being interrupted, the ice tray heater or the inlet water heater, the water fill valve, communication with the door module, and an input voltage that is too high or too low. For many of them the manual says a one-time fault after a power-off and on is temporary, and a repeat means the ice maker is replaced.

The manual is clear that the ice maker should not be replaced before the other causes are ruled out: voltage fluctuations, the water inlet, low water pressure, a blocked ice dispenser flap and a blocked ice crusher. One owner-safe point: the water filter icon turns red after 23 weeks of runtime or 665 gallons and blinks after 26 weeks or 739 gallons. That is a reminder to change the filter, not a fault, and a neglected filter can cut water flow to the ice maker.

Why we don’t recommend guessing parts

Look at how many rows say “or”. F123 and F124 can be an electrical component or the cooling circuit; F127 can be a connection plug or a board; F147 has four possible causes. The code narrows the field, it does not name the part. The manual’s remedies depend on component tests in the technician’s service mode, so a diagnostic visit beats a parts order. We read the stored faults, confirm each against live readings, and quote the actual repair, with the diagnostic fee credited toward it.

A sensor, a fan, an air flap or an ice maker is usually a repair worth doing. A failed sealed system on an older unit is where we talk about replacement. Do not clear codes yourself and do not open panels: the stored history is what lets us diagnose the unit correctly.

Miele refrigerator repair across the Denver Metro

FiXiFY repairs Miele refrigerators and freezers across Denver, Aurora, Lakewood, Westminster and the surrounding metro, with genuine OEM parts. Start with our Miele repair page, the built-in refrigerator and freezer repair page, or refrigerator repair in general. If you own another high-end brand, see our Sub-Zero refrigerator error codes and Liebherr refrigerator error codes guides.

BOOK ONLINECALL (303) 214-1240

FAQ

What does F 01 47 mean on a Miele refrigerator?

In the factory manual it is the F147 entry: insufficient ventilation from a blocked toekick grille, a faulty condenser fan, a faulty power electronic, or a faulty air flap. When the compressor area overheats repeatedly, the unit shuts its components off, so move perishables and book service.

Can I see Miele fault codes myself?

Most are shown on the display as an F followed by four digits, but the manual marks some, including F120 and the door codes F141 to F146, as not visible to the customer. The technician reads the stored faults in a service menu that keeps up to 10.

Why does my Miele refrigerator beep when the door is closed?

The temperature alarm is held back while the door is open and for 30 minutes after it closes, so a tone after that usually means a compartment is really warm. Check the doors and the air vents, and call if it continues.

Do all Miele refrigerators use the same codes?

No. The table in this guide covers the KF 18xx and K 19xx built-in family sold in the US. Older Miele freezers and other generations have their own fault tables and displays, so a technician matches the code to the exact model.

FiXiFY Appliance Repair — 7030 E 46th Ave Dr, Unit A, Denver, CO 80216 · (303) 214-1240 · support@fixifycolorado.com